Sodium Chloride IP BP USP ACS Reagent FCC Food Grade Manufacturers

(FDA) GMP Approved, ISO-9001, ISO-22000 HACCP, & "REACH" registered Kosher & Halal Certified

--------------

Pure Sodium Chloride & IP BP USP ACS Analytical Reagent FCC Food Grade Manufacturers Suppliers, India
Anmol Chemicals are manufacturers of Specialty Chemicals and Pharmaceutical Excipients, in India. Anmol Chemicals Group has manufacturing facilities spread across India, representatives in Houston Chicago USA and toll manufacturers in China. We make IP, BP, USP, Ph Eur, FCC or Food Grade, ACS, AR or Analytical Reagent Grade, LR or Laboratory Reagent Grade and Pure Grades of various chemicals. All our items are analyzed to meet the required standards.

Our manufacturing facility is FDA GMP approved and ISO-9001, ISO 14000, OHSAS 18000, ISO 22000, FSSAI HACCP certified. We are offering products manufactured as per Kosher and Halal approved method. We are pre-registered with "Reach" for export to European countries.

CAS No.: 7647-14-5, EC Code EINECS: 231-598-3, Molecular Weight: 58.44, Chemical Formula: NaCl

Sodium Chloride BP Grade
NaCl -- 58.44 -- 7647-14-5
Action and use: Used in treatment of electrolyte deficiency.

DEFINITION
Content: 99.0 per cent to 100.5 per cent (dried substance).
CHARACTERS
Appearance: White or almost white, crystalline powder or colourless crystals or white or almost white pearls.
Solubility: Freely soluble in water, practically insoluble in anhydrous ethanol.
IDENTIFICATION
A. It gives the reactions of chlorides.
B. It gives the reactions of sodium.

TESTS
Solution S: If the substance is in the form of pearls crush before use.
Dissolve 20.0 g in carbon dioxide-free water prepared from distilled water and dilute to 100.0 ml with the same solvent.
Appearance of solution: Solution S is clear and colourless.
Acidity or alkalinity: To 20 ml of solution S add 0.1 ml of bromothymol blue solution. Not more than 0.5 ml of 0.01 M hydrochloric acid or 0.01 M sodium hydroxide is required to change the colour of the indicator.
Bromides: Maximum 100 ppm.
Ferrocyanides: Dissolve 2.0 g in 6 ml of water. Add 0.5 ml of a mixture of 5 ml of a 10 g/l solution of ferric ammonium sulphate in a 2.5 g/l solution of sulphuric acid and 95 ml of a 10 g/l solution of ferrous sulphate. No blue colour develops within 10 min.
Iodides: Moisten 5 g by the drop wise addition of a freshly prepared mixture of 0.15 ml of sodium nitrite solution, 2 ml of 0.5 M sulphuric acid , 25 ml of iodide-free starch solution and 25 ml of water. After 5 min, examine in daylight. The mixture shows no blue colour.
Nitrites: To 10 ml of solution S add 10 ml of water. The absorbance is not greater than 0.01 at 354 nm.
Phosphates: Maximum 25 ppm.
Sulphate: Maximum 200 ppm.
Aluminium: Maximum 0.2 ppm, if intended for use in the manufacture of peritoneal dialysis solutions, hem dialysis solutions or haemofiltration solutions.
Arsenic: Maximum 1 ppm, determined on 5 ml of solution S.
Barium: To 5 ml of solution S add 5 ml of distilled water and 2 ml of dilute sulphuric acid. After 2 h, any opalescence in the solution is not more intense than that in a mixture of 5 ml of solution S and 7 ml of distilled water.
Iron: Maximum 2 ppm, determined on solution S.
Magnesium and alkaline-earth metals: Maximum 100 ppm, calculated as Ca and determined on 10.0 g.
Potassium: maximum 5.00 × 102 ppm, if intended for use in the manufacture of parenteral dosage forms or hem-dialysis, haemofiltration or peritoneal dialysis solutions.
Atomic emission spectrometry: To pass the test
Heavy metals: Maximum 5 ppm.
Loss on drying: Maximum 0.5 per cent, determined on 1.000 g by drying in an oven at 105C for 2h.
Bacterial endotoxins: Less than 5 IU/g, if intended for use in the manufacture of parenteral dosage forms without a further appropriate procedure for removal of bacterial endotoxins.

Sodium Chloride USP Grade (US Pharmacopoeia)
NaCl -- 58.44 -- [7647-14-5]

Sodium Chloride contains not less than 99.0 percent and not more than 100.5 percent of NaCl, calculated on the dried basis.

Appearance of solution: Dissolve 20.0 g of the substance in carbon dioxide-free water, and dilute with the same solvent to 100.0 mL. This solution is clear Identification: It responds to the tests for Sodium and for Chloride.
Chloride: Dissolve about 3 mg of the substance in 2 mL of water. Acidify with diluted nitric acid and add 0.4 mL of silver nitrate TS. Shake, and allow to stand. Bacterial endotoxins: The level of Bacterial endotoxins are such that the requirement under the relevant dosage form monograph (s) in which the substance is Sterility— Where the label states that the substance is sterile, it meets the requirements for Sterility under the relevant dosage form monograph (s) in which Acidity or alkalinity: To 20 mL of the solution prepared for the test for Appearance of solution, add 0.1 mL of bromothymol blue TS: not more than 0.5 mL of Loss on drying: Dry the test material at 105º for 2 hours: it loses not more than 0.5% of its weight, determined on a 1.000 g sample.
Limit of bromides: To 0.5 mL of the solution prepared for the test for Appearance of solution, add 4.0 mL of water, 2.0 mL of pH 4.7 phenol red TS, and 1.0 mL Change to read:
Limit of phosphates—
Phosphate stock standard solution— Dissolve an accurately weighed quantity of monobasic potassium phosphate in water to obtain a solution having Phosphate standard solution— Dilute 1 mL of the Phosphate stock standard solution with water to 100 mL. Prepare this solution fresh.
Standard solution— Dilute 2 mL of the Phosphate standard solution with water to 100 mL.
Test solution— Dilute 2 mL of the solution prepared in the test for Appearance of solution with water to 100 mL.
Procedure: To the Standard solution and the Test solution, add 4 mL of Sulfomolybdic acid solution, and add 0.1 mL of a mixture of 1 mL of stronger acid stannous Sulfomolybdic acid solution— Dissolve with heating 2.5 g of ammonium molybdate in 20 mL of water. Dilute 28 mL of sulfuric acid with 50 mL of water, then cool. Mix Limit of potassium: (where it is labeled as intended for use in the manufacture of injectable dosage forms, peritoneal dialysis solutions, hem dialysis solutions, Test solution— Transfer 1.00 g of the substance to a 100-mL volumetric flask, add water and swirl to dissolve, dilute with water to volume, and mix.
Standard solution— [NOTE—The Standard solution and the Test solution may be modified, if necessary, to obtain solutions of suitable concentrations adaptable to the Procedure— Using atomic absorption spectrophotometry, measure, at least three times, the emission intensity of the Test solution and the Standard solution using an Iodides: Moisten 5 g of the substance by the drop wise addition of a freshly prepared mixture of 0.15 mL of sodium nitrite solution (1 in 10), 2 mL of 1 N Aluminum: (where it is labeled as intended for use in the manufacture of peritoneal dialysis solutions, hem dialysis solutions, or hemofiltration solutions)& Standard aluminum solution: To 352 mg of aluminum potassium sulfate in a 100-mL volumetric flask, add a few mL of water, swirl to dissolve, add 20 mL of diluted pH 6.0 Acetate buffer: Dissolve 50 g of ammonium acetate in 150 mL of water, adjust with glacial acetic acid to a pH of 6.0, dilute with water to 250 mL, Test solution: Dissolve 20.0 g of Sodium Chloride in 100 mL of water, and add 10 mL of pH 6.0
Acetate buffer. Extract this solution with successive portions of 20, 20, and 10 mL of a 0.5% solution of 8-hydroxyquinoline in chloroform, combining the chloroform Standard solution: Prepare a mixture of 2.0 mL of Standard aluminum solution, 10 mL of pH 6.0 Acetate buffer, and 98 mL of water. Extract this mixture as described Blank solution: Prepare a mixture of 10 mL of pH 6.0 Acetate buffer and 100 mL of water. Extract this mixture as described for the Test solution, dilute the Procedure: Determine the fluorescence intensities of the Test solution and the Standard solution in a fluorometer set at an excitation wavelength of 392 nm The fluorescence of the Test solution does not exceed that of the Standard solution (0.2 µg per g).
Magnesium and alkaline-earth metals: To 200 mL of water add 0.1 g of hydroxylamine hydrochloride, 10 mL of pH 10.0 ammonia–ammonium chloride buffer The volume of 0.01 M edetate disodium consumed in the second titration does not exceed 2.5 mL
(0.01%, calculated as Ca).
Arsenic: 1 µg per g.
Iron:
Test solution: Use a 10-mL portion of the solution prepared for the test for Appearance of solution.
Standard solution: Immediately before use, dilute Standard Iron Solution (see Iron 241 ) 1 to 10 with water. This solution contains the equivalent of 1 ?g of Procedure: To each of the solutions, add 2 mL of a 200 g per L solution of citric acid and 0.1 mL of thioglycolic acid. Mix, make alkaline with stronger The limit is 2 µg per g.
Barium: To 5 mL of the solution prepared for the test for Appearance of solution, add 2 mL of 2 N sulfuric acid and 5 mL of water. To another 5 mL of the Ferrocyanides: Dissolve 2.0 g in 6 mL of water. Add 0.5 mL of a mixture of 5 mL of ferric ammonium sulfate solution (1 g in 100 mL of 0.1 N sulfuric acid) and Sulfate:
Standard sulfate solution A: To 181 mg of potassium sulfate in a 100-mL volumetric flask, add a few mL of 30% alcohol, swirl to dissolve, dilute with 30% alcohol Standard sulfate solution B: To 181 mg of potassium sulfate in a 100-mL volumetric flask, add a few mL of water, swirl to dissolve, dilute with water to volume, Sodium chloride solution: Dissolve 2.5 g of Sodium Chloride in 50 mL of water.
Procedure: To 1.5 mL of Standard sulfate solution A add 1 mL of a barium chloride solution (1 in 4), shake, and allow to stand for 1 minute. To 2.5 mL of the Nitrites: To 10 mL of the solution prepared in the test for Appearance of solution, add 10 mL of water, and measure the absorbance of the solution in a 1-cm Heavy metals: 5 ppm. and colorless.
A curdled, white precipitate is formed. Centrifuge, wash the precipitate with three 1-mL portions of water, and discard the washings. Carry out this operation rapidly in subdued light, disregarding the fact that the supernatant may not become perfectly clear. Suspend the precipitate in 2 mL of water and add 1.5 mL of 10 N ammonium hydroxide. The precipitate dissolves easily with the possible exception of a few large particles, which dissolve more slowly.
used can be met.
the substance is used.
0.01 N hydrochloric acid or 0.01 N sodium hydroxide is required to change the color of this solution.
of chloramine T solution (0.1 mg per mL), and mix immediately. After 2 minutes, add 0.15 mL of 0.1 N sodium thiosulfate, mix, dilute with water to 10.0 mL, and mix. The absorbance of this solution measured at 590 nm, using water as the comparison liquid, is not greater than that of a Standard solution, concomitantly prepared, using 5.0 mL of a solution containing 3.0 mg of potassium bromide per L and proceeding as above, starting with the addition of 2.0 mL of pH 4.7 phenol red TS (0.010%).
a concentration of about 0.716 mg per mL.
chloride TS and 10 mL of 2 N hydrochloric acid. After 10 minutes, compare the colors of 20 mL of each solution: any color in the Test solution is not more intense than that in the Standard solution (0.0025%).
the two solutions, and dilute with water to 100 mL. USP30
or hemofiltration solutions)—
linear or working range of the instrument.] Dissolve 1.144 g of potassium chloride, previously dried at 105º for 3 hours, in water, dilute with water to 1000 mL, and mix. This solution contains the equivalent of 600 µg of potassium per mL. Dilute as required to obtain not fewer than three solutions at concentrations that span the expected value in the Test solution.
air–acetylene flame and a wavelength of 766.5 nm. Prepare a calibration curve from the mean of the readings obtained with the Standard solution, and determine the concentration of potassium in the Test solution. The limit is 0.05%.
sulfuric acid, 25 mL of iodide-free starch TS, and 25 mL of water. After 5 minutes, examine the substance in natural light. No blue color is observed.
mdash;
sulfuric acid, dilute with water to volume, and mix. Immediately before use, transfer 1.0 mL of this solution to a 100-mL volumetric flask, dilute with water to volume, and mix.
and mix.
extracts in a 50-mL volumetric flask. Dilute the combined extracts with chloroform to volume, and mix.
for the Test solution, dilute the combined extracts with chloroform to volume, and mix.
combined extracts with chloroform to volume, and mix.
and an emission wavelength of 518 nm, using the Blank solution to set the instrument to zero.
(prepared by dissolving 5.4 g of ammonium chloride in 20 mL of water, adding 20 mL of ammonium hydroxide and diluting to 100 mL), 1 mL of 0.1 M zinc sulfate, and about 0.2 g of eriochrome black T trituration. Heat to about 40º. Titrate this solution with 0.01 M edetate disodium VS until the violet color changes to deep blue. To this solution add 10.0 g of Sodium Chloride dissolved in 100 mL of water. If the color changes to violet, titrate the solution with 0.01 M edetate disodium VS to a deep blue endpoint.
iron per mL. Combine 4 mL of this solution and 6 mL of water.
ammonia water, and dilute with water to 20 mL. After 5 minutes, any pink color in the Test solution is not more intense than that from the Standard solution.
solution prepared for the test for Appearance of solution, add 7 mL of water. The solutions are equally clear after standing for 2 hours.
95 mL of ferrous sulfate solution (1 in 100): no blue color develops in 10 minutes.
to volume, and mix. Immediately before use, transfer 10.0 mL of this solution to a 1000-mL volumetric flask, dilute with 30% alcohol to volume, and mix. This solution contains 10 µg of sulfate per mL.
and mix. Immediately before use, transfer 10.0 mL of this solution to a 1000-mL volumetric flask, dilute with water to volume, and mix. This solution contains 10 micgm of sulfate per mL.
resulting suspension, add 15 mL of the Sodium chloride solution and 0.5 mL of 5 N acetic acid, and mix (Test solution). Prepare the Standard solution in the same manner, except use 15 mL of Standard sulfate solution B instead of the Sodium chloride solution: any turbidity produced in the Test solution after 5 minutes standing is not greater than that produced in the Standard solution (0.020%).
cell at 354 nm. The absorbance is not greater than 0.01.

Sodium Chloride IP Grade
We also make IP grade of Sodium Chloride

Sodium Chloride ACS AR Analytical Regent Specifications
NaCl
Formula Wt 58.44
CAS Number 7647-14-5

REQUIREMENTS
Assay: min 99.0% NaCl
pH of a 5% solution: 5.0-9.0 at 25C

MAXIMUM ALLOWABLE
Insoluble matter: 0.005%
Iodide (I): 0.002%
Bromide (Br): 0.01%
Chlorate and nitrate (as NO3): 0.003%
Nitrogen compounds (as N): 0.001%
Phosphate (PO4): 5 ppm
Sulfate (SO4): 0.004%
Barium (Ba): Passes test
Heavy metals (as Pb): 5 ppm
Iron (Fe): 2 ppm
Calcium (Ca): 0.002%
Magnesium (Mg): 0.001%
Potassium (K): 0.005%

Manufacturers

ANMOL CHEMICALS
S-8, SARIFA MANSION, 2ND PRINCIPAL SHAIKH HASAN MARG, MUMBAI 400009, INDIA
TEL: (OFF) 91-22-23726950, 23774610, 23723564. FAX: 91-22-23728264

e-mail: info@anmol.org

Copyright and Usual Disclaimer is Applicable

Exporters to USA, UAE, Europe, South Africa, Tanzania, Kenya, Egypt, Turkey, Nigeria, Uganda, Brazil, Chile, Argentina, Dubai etc.

Representatives in New York, Houston - Texas, Chicago - Illinois, Los Angeles.

Fast Selling IP BP USP ACS FCC Food Grades of Chemicals by Anmol Chemicals
Aluminum Chloride ---------- Ammonium Sulfate ----- Ammonium Persulfate
Aluminum Potassium Sulfate - Ammonium Chloride ---- Ammonium Bicarbonate
Ammonium Carbonate --------- Benzyl Alcohol ------- Boric Acid
Benzoic Acid --------------- Borax; Sodium Borate - Calcium Chloride
Calcium Hydroxide ---------- Calcium Acetate ------ Calcium Butyrate
Calcium Lactobionate ------- Calcium Levulinate --- Calcium Saccharate
Carbamide Peroxide --------- Citric Acid ---------- Calcium Phosphate
Calcium Oxide -------------- Calcium Sulfate ------ Chromic Chloride
Cupric Chloride ------------
Ferric Chloride ------------ Ferric Nitrate ------- Fumaric Acid
Gentian Violet ------------- Glacial Acetic Acid
Lactobionic Acid ----------- Magnesium Butyrate
Magnesium Oxide ------------ Magnesium Chloride --- Magnesium Sulfate
Malic Acid ----------------- Maleic Acid ---------- Manganese Chloride
Manganese Sulfate ---------- Methylene Blue ------- Oleic Acid
Octyldodecanol -------------
Propylene Carbonate -------- Potassium Acetate ---- Potassium Carbonate
Potassium Hydroxide -------- Potassium Chloride --- Potassium Phosphate
Potassium Bitartrate ------- Propylene Carbonate -- Selenious acid
Sodium Molybdate ----------- Sodium Perborate ----- Sodium Phosphate
Sodium Propionate ---------- Sodium Acetate ------- Sodium Bicarbonate
Sodium Hydroxide ----------- Sodium Chloride ------ Sodium Thiosulfate
Sodium Selenite ------------ Urea ----------------- Zinc Chloride
Other Best Selling Products
Ammonium Bromide ----------- Ammonium Phosphate --- Barium Chloride
Butylated Hydroxyanisole --- Butylated Hydroxytoluene
Calcium Nitrate Nitrite ---- Calcium Propionate --- Copper Sulfate
Ceric Ammonium Nitrate ----- Cinnamaldehyde ------- Isatoic Anhydride
Directly Compressible Calcium Carbonate ----------- Encapsulated Citric Acid
Encapsulated Fumaric Acid -- Encapsulated Sodium Bicarbonate -
Encapsulated Sorbic Acid
Potassium Bromide ---------- Potassium Iodide ----- Potassium Nitrate Nitrite
Sodium Bromate ------------- Skatole -------------- Sodium Butyrate
Sodium Nitrite & Nitrate --- Sodium Bromide ------- Sodium Diacetate
Sodium Formaldehyde Bisulfite Strontium Chloride -- Stannous Chloride
TBHQ Tertiary Butylhydroquinone

Sodium Chloride
Commercial Pure & USP BP IP ACS Analytical Reagent FCC Food Grade, CAS 7647-14-5